GREENSEAL MS SEALANT

PRODUCT DESCRIPTION
GS MS Sealant is a general-purpose sealant based on advanced MS Polymer technology. It is a single-component elastomeric sealant with excellent adhesion property on various substrates like concrete. After curing, the sealant is permanently elastic and has a movement capability of ±50%.

GỌI NGAY 0913 404 017 - 0985 406 777 ĐỂ ĐƯỢC TƯ VẤN

It is able to comply with the stringent requirements of ASTM C920 as well as the SCAQMD rule #1168 (Architectural Sealant) for low VOC. Unlike polyurethane sealants, it is solvent-less and isocyanate-free; ensuring that the cured sealant will not shrink or have bubbling issues. It is also free of silicone oil, minimising building aesthetic issues caused by oil-staining and dirt-streaking problems often associated with silicone sealants.

APPLICATION

Recommended for sealing concrete joints, cracks like precast wall panel joints, expansion joints, control joints, connection joints, etc. It is also ideal for window frame perimeter sealing especially when the sealant needs to be painted. Other recommended applications include sealing of GRC panel systems, anodized aluminium, masonry, porcelain, coated metal, finished wood, epoxy and polyester panels, UPVC, polystyrene, and stainless steel.

FEATURES

ASTM C920 (Class 50) compliant
Better weathering resistance than PU sealants
Paintable
Low static charge – Less dirt streaking
Silicone oil-free – Non-staining on adjacent substrates
Isocyanate-free – No air bubbling
Solvent-free – No shrinkage
Primerless bonding to most surfaces

TECHNICAL DATA

Curing System	Moisture Curing
Base	One-component MS Polymer
Appearance	Non-sagging paste (before cure) Elastic rubber (after cure)
Density	1.54 gm/ml
Tack-free Time	20 – 60 minutes
Maximum Tensile at Break (ASTM D412)	1.1 N/mm²
Elongation at Break (ASTM D412)	600 %
Shore A Hardness (ASTM C661)	33
VOC Content (USEPA Test Method 24)	< 10gm/L
Joint Movement Capability (ASTM C719)	±50 %
Elastic recovery (ISO 7389)	>70 %
Slump (ASTM D2202)	<1mm
Cure Depth (24 hours) at 23 °C, 50 % Humidity	Approx. 3 mm
Application Temperature	5°C to 40°C
Service Temperature	-30 °C to 90 °C

DIRECTIONS OF USE

1. Surfaces must be clean, dry and free of dirt, grease, oil or water.

2. For a neat finishing, apply masking tape and remove it before sealant skins over.

3. Primer is recommended for porous substrates such as concrete for excellent adhesion.

4. Cut the tip off and puncture the internal foil seal with the nozzle. Cut the nozzle at 45° angle to desired bead-width and apply the sealant to substrate with a cartridge gun.

5. Tool the sealant before it skins.

6. Uncured sealant can be cleaned up with mineral spirits.

7. Use approved backing material for joints over 10 mm deep.

CLEAN UP

 Wet sealants can be cleaned up with acetone or mineral spirits.

 Cured sealants can only be removed mechanically.

LIMITATION

Not recommended for the following applications:

 Below waterline or permanent water immersion.

 Outdoor sealing/bonding adjacent to glass substrates.

 Polyethylene, polypropylene, polytetrafluoroethylene (Teflon), neoprene, and bituminous surfaces.

 Overcoated with

- Alkyd resin paint - cure inhibition to the paint

- Chlorinated paint - staining issue

- Oil based paint - not compatible

JOINT DESIGN

 Joint dimension should be designed by taking into consideration the movement capability of the sealant and the anticipated joint movement

 Generally the joint width-to-depth ratio is 2:1 for joint width ≥12 mm, or 1:1 for joint width <12 mm

 Joint width: minimum = 6 mm, maximum = 35 mm *

 Joint depth: minimum = 6 mm, maximum = 12 mm

* Sealing joints with larger joint width is possible but sealant may sag in vertical applications

COVERAGE.

Width	Depth	Coverage (290 ml) *	Coverage (600 ml) *
6 mm	6 mm	7.32 meter	15.15 meter
10 mm	10 mm	2.64 meter	5.45 meter
20 mm	10 mm	1.32 meter	2.73 meter
25 mm	12 mm	0.88 meter	1.82 meter

CAUTION

Keep out of reach of children. Contains aminosilane. May produce an allergic reaction. Safety data sheet available on request. For further health and safety information, consult the latest safety data sheet.

STORAGE AND CONTENT

 Store in a dry and cool place with temperature below 30°C.

 From the date of production, 12 months in aluminium foil sausage

Trụ sở chính

CÔNG TY TNHH THƯƠNG MẠI & XÂY DỰNG QUỐC THẮNG

257 Điện Biên Phủ, Phường Thanh Khê, Thành phố Đà Nẵng, Việt Nam
Hotline: (+84) 0912333257 / 0913404017
Tel: (+84) 2363.725 881 - Fax: (+84) 2363.725 882
E-mail: email@quocthangco.vn

Truy cập nhanh

Giới thiệu

Thiết kế và phát triển bởi VinaWise